Tradefox

Tradefox – Build Skills

Learn Construction

‹ All carpentry calculators

Load arithmetic

Shelf deflection: simple elastic model

I=bh312δ=5wL4384EIM=wL28σ=Mbh26
where
I
second moment of area (mm⁴)
b
width (mm)
h
vertical depth (mm)
δ
midspan deflection (mm)
w
uniform line load (N/mm)
L
span (mm)
E
elastic modulus (N/mm²)
M
maximum bending moment (Nmm)
σ
bending stress (N/mm²)
Explain this equation

Estimates how much a simply supported shelf or similar member sags under an even load, along with the bending moment and stress.

b is the width and h the vertical depth of the section, in millimetres. I is the second moment of area, which measures how well the shape resists bending. L is the span, E the stiffness of the material and w the load per millimetre of span. δ is the midspan sag, M the maximum bending moment and σ the bending stress.

I = bh³/12 means depth matters far more than width. Doubling h makes the shelf eight times stiffer. The 5/384 and 1/8 factors are standard results for an even load on a simply supported span. bh²/6 is the section modulus, which turns moment into stress.

A 1000 mm span of 300 × 20 mm at E = 10,000 N/mm² under 0.5 N/mm sags about 3.3 mm. Double the span and the sag rises sixteen-fold.

Watch out: this is a guide, not a design check. There is no creep, shear or safety factor.

Calculate an ideal simply supported rectangular member under a uniform load.

mm
mm
mm
N/mm²
N/mm

Enter your values to see the result.

Good to know

All lengths mm; w in N/mm (numerically equal to kN/m); E in N/mm². Ideal short-term bending only: no creep, shear, support restraint, grading, safety factors or resistance check. Not structural sizing or a safe-span verdict.

Limits

The two beam tools implement ideal short-term linear elastic bending of a simply supported rectangular section. They do not include creep, shear deflection, load combinations, material strength, buckling, service class, duration factors, connection capacity, bearing or actual restraint. They produce no safe/unsafe verdict and must not be used as structural sizing tools. Beam calculations use the stated ideal supports and loads; they do not select a safe timber size.

Sources

This is a calculation aid, not a structural design or compliance certificate. Every default is an example, not a specification for your project.

Worked example

A 900 mm alcove shelf in planed softwood 220 mm wide × 21 mm deep, taking E as 8000 N/mm² and a load of 0.3 N/mm (roughly 30 kg of books per metre): I = 220 × 21³ ÷ 12 ≈ 169,785 mm⁴; δ = 5 × 0.3 × 900⁴ ÷ (384 × 8000 × 169,785) ≈ 1.9 mm; M = 0.3 × 900² ÷ 8 ≈ 30,375 Nmm; σ ≈ 1.9 N/mm². A sag of about 2 mm over 900 mm is unlikely to be noticed when the shelf is first loaded, though timber will creep over time.

Common questions

What value of E should I use for my shelf material?
Take it from the board or timber grade data where you can, as it varies a lot between softwood, hardwood, plywood, MDF and chipboard. Particle boards are much less stiff than solid timber, so the same size shelf sags more.

Does fixing the shelf ends into the walls reduce the sag?
Ends that are firmly fixed will sag less than this simple supported model predicts, but loose bearers or shelf pins behave close to simply supported. Using the simple model keeps the estimate on the cautious side.

What is the quickest way to cut the sag in half or better?
Increase the depth or add a front lipping on edge, because depth is cubed. Shortening the span also works well, as deflection rises with the fourth power of the span: a centre support makes a big difference.

Scroll to Top
Secret Link